WallDamp Installation Guide

WallDamp is added to faces of studs and plates in standard (single wall board), single stud, single plate construction.

1. WallDamp Strips on studs (both sides)
2. WallDamp Strips on plates (both sides)
3. Insulation batt in wall cavity
4. Single layer wall board

Same as above, but a second layer of wall board is added to one side of the wall, with WallDamp sandwiched between wall boards.

1. WallDamp Strips on studs (both sides)
2. WallDamp Strips on plates (both sides)
3. WallDamp Squares between wall boards
4. WallDamp Strips between wall boards
5. Insulation batt in wall cavity
6. First layer wall board
7. Second layer wall board
8. Single layer wall board

Same as above, but both sides of the wall have two layers of wall board, with WallDamp sandwiched between wall boards.

1. WallDamp Strips on studs (both sides)
2. WallDamp Strips on plates (both sides)
3. WallDamp Squares between wall boards
4. WallDamp Strips between wall boards
5. Insulation batt in wall cavity
6. First layer wall board
7. Second layer wall board

WallDamp is added to faces of studs and plates in standard (single wall board), double stud, single plate (staggered studs) construction.

1. WallDamp Strips on studs (both sides)
2. WallDamp Strips on plates (both sides)
3. Insulation batt in wall cavity
4. Single layer wall board

Same as above, but a second layer of wall board is added to one side of the wall, with WallDamp sandwiched between wall boards.

1. WallDamp Strips on studs (both sides)
2. WallDamp Strips on plates (both sides)
3. WallDamp Squares between wall boards
4. WallDamp Strips between wall boards
5. Insulation batt in wall cavity
6. First layer wall board
7. Second layer wall board
8. Single layer wall board

Same as above, but both sides of the wall have two layers of wall board, with WallDamp sandwiched between wall boards.

1. WallDamp Strips on studs (both sides)
2. WallDamp Strips on plates (both sides)
3. WallDamp Squares between wall boards
4. WallDamp Strips between wall boards
5. Insulation batt in wall cavity
6. First layer wall board
7. Second layer wall board

WallDamp is added to faces of studs and plates in standard (single wall board), double stud, double plate construction.

1. WallDamp Strips on studs (both sides)
2. WallDamp Strips on plates (both sides)
3. Insulation batt in wall cavity
4. Single layer wall board

Same as above, but a second layer of wall board is added to one side of the wall, with WallDamp sandwiched between wall boards.

1. WallDamp Strips on studs (both sides)
2. WallDamp Strips on plates (both sides)
3. WallDamp Squares between wall boards
4. WallDamp Strips between wall boards
5. Insulation batt in wall cavity
6. First layer wall board
7. Second layer wall board
8. Single layer wall board

Same as above, but both sides of the wall have two layers of wall board, with WallDamp sandwiched between wall boards.

1. WallDamp Strips on studs (both sides)
2. WallDamp Strips on plates (both sides)
3. WallDamp Squares between wall boards
4. WallDamp Strips between wall boards
5. Insulation batt in wall cavity
6. First layer wall board
7. Second layer wall board

WallDamped furring strips are applied to existing block wall (concrete wall, CMU wall, etc.). Two layers of wall boards are added with WallDamp sandwiched in between.

1. WallDamp Strips on furring strips
2. WallDamp Squares in between wall boards
3. First layer wall board
4. Second layer wall board

WallDamp Strips and Squares are applied to existing wall, then a new layer of wall board is added.

1. WallDamp Strips over locations of studs and plates
2. WallDamp Squares over existing wall board
3. Existing wall board
4. Added second wall board